Eiki LC-XB43N Owner's Manual Page 62
- Page / 150
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
62
Chapter 6 Basic setting and operation
✐ Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without
resetting the lamp counter, the alert mail is sent to users in every power-on of the projector. This
alert mail will not be sent when the mail sending condition "When the life span of lamp is reached" is
unchecked.
● When PJ lamp replacement time is reached:
TITLE: Message from projector
10-03-2007 00:59
Projector Model Name: model name
TCP/IP: 192.168.1.201 Projector Name: Proj05
It sends you following message.
*The PJ lamp replace time is reached.
Examples: Type and contents of alert mail
When the projector has an abnormality, the following alert messages are sent to the registered E-mail
address depending on your selected condition. Administrator or user can take an efficient action
quickly by receiving this message. This is very useful to maintain and service the projector.
The following are examples of received messages.
5 Option selection for sending alert mail
Click Option sub menu tab. Check the condition items under
which alert mail will be sent and click Set button.
Please refer to the item "Examples :Type and contents of alert
mail" described as below.
Option
[1]––––––––––––––––––––––––––––––––––
o When PJ lamp is off.
o When PJ lamp replacement time is reached.
o When PJ needs service.
o When internal PJ temperature is too high.
o When PJ is turned into Standby in proper user
operation.
[2]––––––––––––––––––––––––––––––––––
o When accumulated filter use time reaches
[ ] hours.
o When Power management function turns PJ
lamp off.
o When the signal is interrupted.
o When Auto Play is failed.
[3]––––––––––––––––––––––––––––––––––
o When lamp Corres. Value reaches
[ ] hours.
Attached message
✐ "When PJ lamp is off" signifies the lamp goes out
without user operation. "When PJ is turned into
Standby in proper user operation" signifies that the
projector is turned on by using the web browser
and then it is turned into standby with ON/STANDBY
button on the top control or the remote control.
✐
If condition "When Auto Play is failed" is checked, the
trap is sent when the error occurs during the auto
display operation using with the network viewer
function (+p.113). For further information of the
error, refer to item "Auto Display setting and control
page [3]"(+p.128).
✐ The length of message should be less than 255
characters.
✐ Up to 99,999 hours can be set for use time.
✐
The optional settings return to the factory default
when you unplug the AC power cord of the projector.
- Network Set-up and Operation 1
- For Windows 1
- Compliance 2
- European Community (EC) 3
- European Community 3
- Safety instructions 4
- Table of contents 5
- Chapter 11
- Flow of Image Transfer 12
- An example of the connection 13
- LAN connection modes 14
- LAN connection modes 15
- Chapter 1 About LAN functions 16
- Installing the software 19
- ● Network Capture 5: 20
- ● Network Viewer 5 (Program 20
- File Converter 2 installation 21
- Installed software and places 21
- Network Capture 5 window 25
- Note on Windows Vista 26
- Setting Procedure 28
- Confirming the operation 30
- Specify IP button 31
- Network Projector list 31
- Network PIN code 32
- Network information 32
- Wired factory default 33
- USB Display 34
- Setting procedures 36
- WEP configuration screen 38
- WPS Push button 39
- WPS PIN code 40
- Available PSK key characters 42
- Hex code .........64 digits 42
- Setting Procedures 43
- Wireless factory default 44
- WIRELESS indicator display 45
- Easy wireless setting 46
- Starting up the Browser 48
- Display of main setting page 49
- Page numbers 49
- How to use the setting page 50
- Type of the setting pallet 51
- Initial setting 52
- Network PIN code setting 53
- PJLink and password setting 53
- Date and time setting 54
- Network configuration 55
- Set button 58
- Setting of WPS PIN code 59
- Setting of WPS Push button 59
- E-mail setting 60
- 3 Registering POP server 61
- ● When PJ needs service:: 63
- SNMP setting 64
- Trap check/delete 65
- Trap option 66
- Trap option setting 66
- PJ status 68
- PJ temp 68
- About projector condition 69
- Controls 70
- Image adjustment 72
- Item Description 73
- PC adjustment 74
- Setting up the projector 75
- Start button 76
- How to set the timer 78
- 2 Set an execute time 79
- 3 Select an event action 79
- 4 Register an event 79
- Notes on timer setting 80
- Projector information 81
- Indication of the lamp status 82
- Select Input2 for 83
- PJ1 to PJ4 83
- Start/stop the multi control 84
- Register the projector 85
- Controlling all together 87
- Setting all together 87
- - Real Time Capture (+p.93) 90
- - Moderator Function (+p.107) 90
- Commands on the task bar 91
- Parameter set up 92
- Registering the computers 93
- 1 Start up Network Capture 5 94
- Set "On" when 95
- [3] Control by the projector 96
- ＊USB memory provides 97
- Auto Capture program 97
- Project this screen 97
- 4 Start the presentation 98
- Capture a screen 99
- Menu tree 100
- Tool bar button names 101
- End the communication 102
- Start the communication 102
- Edit capture image 103
- Drawing letter 104
- On the Communication 105
- Preparation 105
- Executing the forcing mode 106
- Moderator function 107
- Using the moderator function 109
- Unregister moderator status 110
- Error information 111
- File Converter 1 window 114
- Preview window 114
- Creating the available data 115
- Menu Tree 115
- Command Tool Button 115
- Output destination 117
- Conversion mode 117
- 2 Click Connect button 119
- Display order 121
- File name 121
- FTP le server 124
- *1 IMPORTANT NOTICE 125
- [2] Control by the projector 128
- Display length 129
- Repeat times 129
- FTP server 131
- Use of telnet 134
- Command list table 135
- Web browser setting 136
- Examples: OS/Browsers 137
- Proxy setting 138
- Netscape Navigator v.7.0 139
- JavaScript Setting 139
- Flash Player enable 139
- Firewall setting 141
- Troubleshooting 142
- Infrastructure Mode: 143
- ■ Cannot start up the browser 143
- Network capture 144
- Network Viewer 145
- File Converter 1 146
- File Converter 2 146
- Auto Capture 147
- USB display 147
- Terminology 148
- IEEE802.11b 149
- IEEE802.11g 149
- IEEE802.11n 149
- WPS (Wi-Fi Protected Setup) 149
- SO-WIN-KC8BC 150
Related products and manuals for Data projectors Eiki LC-XB43N
Data projectors Eiki WL-10 Owner's Manual
(79 pages)
(79 pages)
Data projectors Eiki LC-SB22 Owner's Manual
(64 pages)
(64 pages)
Data projectors Eiki LC-XB42N Owner's Manual
(108 pages)
(108 pages)
Data projectors Eiki EIP-1 Owner's Manual
(109 pages)
(109 pages)
Data projectors Eiki EIP-25 Owner's Manual
(35 pages)
(35 pages)
Data projectors Eiki LC-XB26 Owner's Manual
(64 pages)
(64 pages)
© 2020, manymanuals.com. All rights reserved. | 0.839 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals