Eiki LC-WAU200 Owner's Manual

Owner's ManualMultimedia ProjectorLC-XAU200LC-WAU200Model

9Part names and functionsFrontBackBottom⑨⑬⑫⑥① ② ③④ ⑤⑦⑧⑩⑪CautionHot air is exhausted from the exhaust vent. Donot put heat-sensitive objects near this

10Part names and functionsTerminals①② ③④⑤ ⑥ ⑦⑧⑨ ⑩① AUDIO OUT (Page 18) - Connect external audio amplier to this jack. - Output audio signa

11Part names and functionsControl Panel and Indicators① POWER indicator - Lights red when the projector is in stand- by mode. - Ligh

12Remote control① POWER Turn on or turn off the projector.(Page 20,21)②VGA Select VGA as input source.(Page 28)③INPUT Enter input source menu to

13⑱⑭⑯⑲⑳⑰⑫⑮⑬⑫TIMER Enable the timer function.(Page 27) ⑬FREEZE Freeze the projected image.(Page 26)⑭MUTEMute the sound.(Page 25,26) ⑮AUTO Enter auto se

14 Install remote control batteriesOperating range① Open the battery compartment lid. ② Install new batteries into the compartment.③ Replace

15InstallationPositioning the projectorNote:● The brightness in a room has a great inuence on picture quality. It is recommended to limit the a

16InstallationConnecting to computer(Digital and analog RGB)Cables used for connection:● VGA cable

17 HDMI outputHDMIcableHDMIInstallationConnecting to video equipment Cables used for connection:● Video cable*

18(R) (L)(R) (L)Audio cableAudio cable(stereo)Audio cable(stereo)Note: The left and right channels are combined when there is only the L(mono

19InstallationConnecting the AC power cordThis projector uses nominal input voltages of 100–240V AC and it automatically applies to different input vo

20Note:● When the logo select is set to be "Off", the logo will not be displayed on the screen. ● When the Display function is set to be

21Basic operationTurn off the projectorPower off ?“Power off ? ” disappears after 4 seconds.1. Press the POWER button on control panel or on the r

22Remote controlScreen menuControl panelMEMUOK  1 Press the MENU button on the top control or the remote control to display the screen menu.

23Menu bar① PC adjust Adjust computer parameters to match with VGA input signal format: Auto PC adj, Fine sync, Total dots, Horizontal

24Auto setup functionAdjust focusThis function is available just by pressing the AUTO button on the remote control. The system then automatically per

25VolumeRemote controlMUTEVOLUME +/- Menu operationVolume menuVolumePress  to increase the volume and  to decrease the volume.MutePress button to

26Remote control operationINPUT Press INPUT button on the remote control to select the input source.FREEZE Press FREEZE button to freeze the picture o

27D.ZOOM+ Press D.ZOOM+ button, the on-screen menu will disappear, while the information on digital zoom + appears. You can press Select to zoom in th

28Input selectDirect OperationPress HDMI, VGA, COMOPNENT, S-VIDEO or VIDEO button to select HDMI, VGA IN, Component, S-video or Video as input source.

2Features and DesignNote: - The screen menu and pictures in the manual may slightly differ from the real product. - The manual is subject to change

29PC AdjustAuto PC adj.Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal and Vertical to conform to yo

30PC AdjustSome computers employ special signal formats which may not be tuned by Multi-scan system of this projector. Manual PC Adjustment is provide

31Screen SizeDisplayFollowing items can be set in Display menu:Screen Size, Keystone, Project Mode, Menu Position, Background Display and System.Displ

32DisplayKeystone menuProject mode menuThis function is used to store or reset the keystone correction when the AC power cord is unplugged. 1 Press M

33DisplayMenu PositionMenu position PC adjustDisplayColor adjustSettingExpandInfo.Adjust Select BackScreen Size NormalKeystone

34SystemComputer system selectThe projector automatically tunes to various types of computers with its function of Multi-scan system and Auto PC Adjus

35Note: When HDMI is selected, System menu for AV is disable.PC adjustDisplayColor adjustSettingExpandInfo.Adjust Select Back System Compo

36Color adjust menu is used to set the image mode and adjust the image. Menu operationImage mode (Computer)Image mode (Video, S-video, Component)PC ad

37Color adjustColor adjust (Computer)PC adjustDisplayColor adjustSettingExpandInfo.Move Next ExitImage Mode NormalContrast

38PC adjustDisplayColor adjustSettingExpandInfo.Move Next ExitImage Mode NormalContrast 32Brightness

3ContentsFeatures and Design 2Contents 3Safety Instructions 4Safety Guide 5Air circulation 6Moving the projector 6Installing the projector proper

39The projector has Setting menu that allows you to set the other various functions described as follows.Setting menuOn startStandby modeSettingPC adj

40Setting High landEnable to control the fan through the Setting menu.You can select the running speed of the fan according to the altitude of the loc

41SettingKey lockPC adjustDisplayColor adjustSettingExpandInfo.Adjust Select BackOn start OffStandby mode NormalHigh

42 IrisThis function is used to increase the contrast of the image. On...Enable Iris function, increase the contrast of the image. Off..

43ExpandThe projector has Expand menu that allows you to set the other various expand functions described as follows.Expand menuAuto setupPC adjustDis

44Expand LogoThis function allows you to customize the screen logo with Logo select, Capture, Logo PIN code lock and Logo PIN code change functions.Lo

45This function allows you to use the PIN code lock and PIN code change functions to set the security for the projector operation.PIN code lockThis fu

46ExpandNote: Factory default: "Ready: 5 min". Filter counterThis function is used to set a frequency for lter cleaning.When the projecto

47Expand Test PatternThis function is used to set the internal test signal:Gray scale 1,Gray scale 2,Gray scale 3,Gray scale 4, Color bar, Red, Green,

48Expand Factory defaultThis function returns all setting values except for the User logo, PIN code lock, Logo PIN code lock, Lamp counter and Filter

4Safety InstructionsPlease read this manual completely before installing and operating the projector.The projector provides many convenient features a

49InformationThe information menu is used to detect signal of projected image and running state.Menu operation1. Press MENU button on the remote contr

50Network Control Connecting to the LANConnect the LAN cable to the LAN terminal of the projector. Computer operation1. Turn on the computer.2. Set th

51 Webpage operation1. Input IP address in address bar. Refer to page 50 for obtaining IP address.2. Input ID and password,click OK to display the we

52Projector/DisplayProjector/ColorAdjProjector/InputThis page displays Screen size, Menu position and Background.You can select Image Mode, adjust val

53Network ControlProjector/SettingYou can set Input Search/Auto PC adj/On start/Lamp control/Blank/Freeze in this page.

54Maintenance and cleaningCautionDo not leave the projector with the AC power cord connected under an abnormal condition. It may result in re or elec

55Maintenance and cleaningCleaning the lterFilter counter resetThe air lter prevents dust from accumulating on the surface of the optical elements i

56Maintenance and cleaningClean the project lensClean the cabinetUnplug the AC power cord before cleaning.Gently wipe the projection lens with a clean

57Replace the lampWhen the projection lamp of the projector reaches its end of life,the Lamp replacement icon appears on the screen, please replace th

58Maintenance and cleaningLamp counter reset1 Press the MENU button to display theon screen menu. PressST buttons to select Expand icon and the

5Safety GuideAll the safety and operating instructions should be read before the product is operated.Read all of the instructions given here and retai

59This projector uses a high-pressure lamp which must be handled carefully and properly.Improper handling may result in accidents, injury, or create a

60Problems – SolutionsNo power - Plug the power cord of the projector into the AC power outlet.- Check whether the POWER indicator lights red.- Only w

61No Sound - Check the audio cable connection from audio input source.- Adjust the audio source.(Page 25)- Press the VOLUME + button.(Page 25)- Press

62IndicatorState of projectorPOWER(Green/Red/Orange)WARNING(Red)Powered off (not in standby mode)The projector is off. (AC power cord not connected).P

63Compatible computer specicationsThis projector can receive the signals below:Appendix√ Note: The specication is subject to change without any p

64 Technical SpecicationsAppendix● The aforesaid specication is subject to change without prior notice.● Liquid crystal panel is made on the basis o

65Congurations of terminalsCOMPUTER IN 1/SCART, COMPUTER IN 2/MONITIOR OUTTerminal: Analog RGB (D-sub 15 pin)51234109 67815141311121 Red (Input/outpu

66AppendixUnit: mmScrew Holes for Ceiling MountScrew: M4Depth: 10.0Dimensions26728088261572263299.5126.3136.3391.2329.2

67Menu TreeAppendixAuto PC adj.Fine sync Total dotsHorizontalVerticalDisplay area HDisplay area VResetMode free Store

68AppendixLanguage English / French / Spanish / Portuguese / German / Italian / Japanese / Korean / Russian / Finnish / Dutch / Th

6Safety GuideAir circulationVents in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from over

69AppendixPIN code memorandumWrite down the PIN code in the blank below and keep it, If you forgot or lost the number and unable to operate the projec

U.S.A.EIKI International, Inc.30251 EsperanzaRancho Santa MargaritaCA 92688-2132U.S.A.Tel: 800-242-3454 (949)-457-0200Fax: 800-457-3454 (949)-457-7878

7ComplianceThe AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it. AC Power Cord for the United

8Owner's Manual(CD) AC Power cordRemote control with batteries(AAA or LR03)VGA cable Quick start guideAccessories