Eiki LM-2 Instruction Manual

, .-OWNER'S INSTRUCTION MANUAL I , 16mm Sound Projector " NST· 0/1 12 13 NT· 0/1 12 13 '

3. Set function switch to STOP posit ion, e • * 4, Connect power plug to proper outlet, 5, To turn lamp on, rotate function switch to the FORWARD lamp

7. Adjust focus for clean and sharply illuminated screen. ~~~~~--------FOCUSKNOB 8. Return function switch to STOP. NOTE: Make sure the flywheel (se

THREADING :FULLY AUTOMATIC THREADING (REEL-TO-REEL) MODELS NST -0/1/2/3 1. Place EIKI-MATIC AUTO take-up REE L on take-up arm. Insert film in trimmer

THREADING: SELF THREADING MODELS NT -0/1/2/3 1. Insert film in trimmer and cut. (Fig. A) NOTE: New trimmer can be used with Estar or Mylar-base film.

PROJECTING 1. Turn function switch to FOR-WARD position (.r.g ) and LAMP on position ( ~~ , (]~ ). 2. Focus picture. Frame film by adjusting the f

7. For larger groups the extension speakers located in the front cover (1, 2, 3 types only) may be placed near the screen and plugged into t

REWINDING (USA & CANADA ONlY) 1. Attach tail end of film to the sup-ply reel. 2. Push rewind lever DOWN to RE-WIND position (Fig. A) . Engaging

CHANGING LAMPS e. * Disconnect power cord. PROJECTION LAMP (ELC/24V 250W) To open the lamp house door, remove the lock screw and pullout from the to

The lamp position may be adjusted for maximum evenness of illumina-.tion, allowing for small variations in lamps. LAMP ADJUST II SCREW ' EXCITER

HI-LO LAMP SWITCH LAMP HI-LOW SWITCH (for maximum life) By switching to LOW position ( i(j~ ) . your lamp will last 3 times longer and even in th

When the show must go on. NST·O/1/2/3-NT·O/1/2/3 Simple Operation Easy Maintenance Trouble-Free Use This Operator's Manual is easy to read, inf

SILENT FILM OPERATIONS e •• DISCONNECT POWER SUPPL Y CORD SOUND SILENT Shutter ==~I Shutter __ _ f--__ Motor If-------Motor This is changed by slippin

RECOMMENDED SPARE PARTS AND ACCESSORI ES Projection Lamps - E LC/ 24 V 250W I f replacement E LC lamp is not available, a 24V-200W EJ L lamp may

SPECIAL APPLICATIONS A. USING PROJECTOR AS A P.A. SYSTEM Using projector as a P.A. system, simply plug an accessory microphone into the amplifier mi

B. MAGNETIC SOUND TRACK PLAYBACK (NST-2/3, NT-2/3) 1. To reproduce a previously recorded magnetic sound track, turn the Opt/ Mag switch to the (M

D.50HZ TO 60HZ CONVERSION The standard NST & NT projector is available either as 50Hz sound and silent or 60Hz sound and silent operations. C

CLEANING AND MAINTENANCE The ElK I projector has been designed to provide years of trouble free services . . All maintenance such as lubrications an

OPERATOR TROUBLESHOOTING GUIDE SYMPTOM CHECK -------r No power to motor or lamp 1. Be sure projector is plu gged in (Pilot lamp not on) and t he out

Poor sound Poor picture Poor illumination SYMPTOM CHECK 1. Check position of volume con-trol 2. Chec~ position of tone controls 3. Check for correct e

MEMO

MEMO

IMPORTANT SAFEGUARDS When using your E I KI 16mm projector, basic safety precautions should always be followed, including the following: 1. Read

r MEMO

MEMO

IMPORTANT SAFEGUARDS (cont'd) 10. To avoid electric shock hazard, do not disassemble this projector, but refer to a qualified service t

SPECIFICATIONS NST Models NT Models Power Source Reel-to-Reel Automatic Thread ing Self Threading Projectors available from 100 to 240V 50, 60Hz, dua

MAIN PARTS OF THE PROJECTOR o ---------1. Supply arm lock button 11. Film trimmer 2. Supply arm 12. Elevator knob 3. Film channel and rewind lever 13.

~-----------------------~ 16. Cam tank module 22. Amplifier fuse 17. Rewind gear 23. Flywheel 18. Transformer module 24. Motor-fan module 19. Amplifie

EXPLANATION OF SWITCH PLATE Model NST tNT -0, 1 o Model NST /NT-2 Model NST /NT-3 All Models 1. Lamp low (Reverse) 2. Reverse 3. Stop 4. Forward 5. L

SETTING UP THE PROJECTOR 2. Raise both reel arms until they snap in place. 5